Working With Two CODE Levels

Working With Two CODE Levels

One of the biggest limitations of the MT macro script is that the script parser can't handle more that 2 levels of {}. So this will work:

 [If(condition), CODE:{
   [if(another_condition), CODE:{
      [code to execute when true]
   };{}]
 };{}]

And this won't:

 [If(condition), CODE:{
   [if(another_condition), CODE:{
     [if(another_condition), CODE:{
       [code to execute when true]
     };{}]
   };{}]
 };{}]

• Note that this is an example, there are other occasions where one uses {}, e.g. {myVar} instead of [r:myVar]. This is subject to the same problem. The only exception I've encountered is with json objects: myVar = json.set("{}", "someKey", someVar). This is NOT subject to this problem. However I believe that if you use '{}' instead of "{}" it won't work (or the other way around).

So what to do when you do need to go deeper?

Basically there are 3 general tricks you can use if you need to go deeper:

method 1: Create another UDF

One of the most common tricks is to create a User Defined Function (UDF) and call this in the nested level. Within this UDF you can yet again go 2 CODE levels deep.

method 2: Code smarter

Many many examples can be given here, but you can achieve a lot by using roll options e.g.:

 [if(condition): if(another_condition, "show this", "else show this"); if(yet_another_condition, "show this", "else show this")]

You can also work with multiple roll options, but this should not work, but does sometimes work e.g.:

 [foreach(item,items), if(item == someVar), CODE:{};{}]

works while:

 [if(listCount(items)>2), foreach(item,items), CODE:{};{}]

won't work.

A lot can be achieved by restructuring your code in this manner.

method 3: Store commands

One final method I recently learned from Ahzrei is a rather dirty method but can be used in certain circumstances. In my case I have code that needs to be executed that is already two levels deep and then I ALSO want to execute this for certain selected tokens. In this case you can first store the to-execute-commands in a json object and then exit the two loops. Now you have a json object containing all code that needs to be executed onto certain tokens. For this you can start a new loop that uses json.evaluate() per json object per token id.

Needs Clarification:
(need to add example later on)

method 4: More than 2 CODE levels

Officially this is NOT supported in MT and thus it could break your code if improperly used. That said, I've been using this method for 6 (dd: 2017) years now and my code is flooded with it and have not yet encountered any issue, so its reasonable to assume that its safe to use. Disclaimer: Still this is at your own risk.

As it turns out it IS possible to have more then 2 nested code levels but in order to do that you have to mislead the parser. This is done as follows:

[if(1), CODE:{
	[if(1), CODE:{
		[if(1), CODE:{
  			  you should never see this in the chat...but you do!
		''
		};{''}]
	''
	};{''}]
''
};{''}]

Important notes:

• put the '' in the ELSE statements as well when they're not empty.
• do NOT use the single quote ' anywhere in the nested code!! It *can* be used, but it *can* also lead to errors! I've not been able to determine when it goes right and when wrong, so to be safe: don't use them.
• if you use multiple embedded if(),code statements, make sure that you use add the else: {} part as well (like in the above example), even if its empty. Due to this 'hack' its possible that if not all elses are given but some are that the an else is used of an embedded if statement instead of the one intended!!

What it boils down to is to add two single quotes '' at the END of EACH code block. This will fool the MT parser and it will accept this nesting. I've tried it upto 9 nestings without a problem (more is probly also no issue). Do keep in mind that this can seriously impact the stack though, so don't go writing huge code blocks this way. I mainly use it for cases where you only have a few lines of code but are required to go 3 or 4 nestings deep and its just annoying to create a separate macro for one or two lines of code.

Note that if in the above example the '' will show up in the chat. You can also use [h:''] instead to prevent this.

--Wolph42 16:22, 19 March 2011 (UTC)